Nema 23 Stepper motor, 1A, 1.8 degree, 2 phase 6 wires

Nema 23 Stepper motor, 1A, 1.8 degree, 2 phase 6 wires
Nema 23 Stepper motor, 1A, 1.8 degree, 2 phase 6 wires
from
$63.31
Ex Tax: $63.31
  • Stock: In Stock
  • Model: SCJ009412
  • SKU: SCJ009412
Products Sold: 0
Product Views: 450

Available Options

  • Description

Nema 23 Stepper motor, 1A, 1.8 degree, 2 phase 6 wires

Brief

Favorable price Nema 23 stepper motor, 0.9Nm holding torque, 1.8 deg. step angle.

Description

Nema 23 Stepper motor, 1A, 2 phase 6 leads, 1.8 degree.

Specification

Electrical SpecificationModelSOCOJE57STH56-1006
Matched Driver ModelSCJ009412(Click it to see more info)
Step Angle1.8°
Holding Torque0.9Nm
Rated Current/phase1A
Phase Resistance7.4Ω
Inductance10mH
Rotor Inertia280g-cm2
Physical SpecificationFrame Size57 x 57mm
Length56mm
Shaft DiameterΦ6.35mm
Shaft Length19mm
Motor Leads6
Weight0.68kg
Technical ParametersStep Angle Accuracy±5% (full step, no load)
Resistance Accuracy±10%
Inductance Accuracy±20%
Temperature Rise80℃ Max. (rated current, 2 phase on)
Ambient Temperature-20℃~+50℃
Insulation Resistance100MΩ Min. 500VDC
Dielectric Strength500V AC for one minute
Shaft Radial Play0.02Max. 450g
Shaft Axial Play0.08Max. 450g
Quality AssuranceWarranty Period12 months
CertificateCE, ROHs, ISO/SGS9001

Dimensions: (Unit=mm)

Nema 23 Stepper motor, 1A, 1.8 degree, 2 phase 6 wiresL Max=56mm

Wiring Diagram

Nema 23 Stepper motor, 1A, 1.8 degree, 2 phase 6 wires

Tips: Reasons for out of step of stepper motor

  1. The working torque of the stepper motor is not enough and there is not enough ability to drive load.
  2. The acceleration and deceleration process for starting and stopping of stepper motor is not sufficient. The stepper motor runs out of steps during acceleration and deceleration process.
  3. Power of the stepper motor is not enough, thus the input power of stepper motor is not enough, leading to out of step of the motor.
  4. Drive voltage of the stepper motor is not enough or the drive current is too low.
  5. Driver or controller receives the signal interference.
  6. Load capacity of motor is reduced due to the system resonance of the stepper motor, thus the step out of the motor is caused.
  7. Stepper motor driver is not matched with the signal of controller.
  8. The gap or the back-and-forth clearance error of synchronizing gear or reducer is not compensated through programming or the compensation value is not correct.
  9. There is something wrong with the control programming.
  • Reviews

Write a review

Note: HTML is not translated!
Rating
Bad Good
Captcha
refresh-code
Nema 23 Stepper Motor, 2.8A, 1.8 degree, 2 phase 4 wiresBrief 2-phase 4-wire Nema 23 stepper motor, with 1.8 deg. step angle(200 steps/revolution). Ea..
from
$73.92
Ex Tax:$73.92
Add to Cart
Nema 23 Stepper motor, 2A, 1.8 degree, 2 phase 6 wiresBrief Low cost and high quality Nema 23 stepper motor, 2 phase 6 wires, 0.9Nm holding torque, 1...
from
$63.31
Ex Tax:$63.31
Add to Cart
Nema 23 Stepper Motor, 3A, 1.8° step angle, 2 phase 6 wiresBrief Nema 23 stepper motor with 0.9Nm holding torque, 1.8 deg. step angle(200 steps/revolu..
from
$73.92
Ex Tax:$73.92
Add to Cart
Nema 23 Stepper Motor, 4.2A, 1.8 degree, 2 phase 4 wiresBrief Favorable price Nema 23 stepper motor, 3.0Nm holding torque, 4.2A phase current, 1.8 deg..
from
$88.08
Ex Tax:$88.08
Add to Cart